#561379 - 19/01/17 04:27 PM
P1602 immobilizer/ecm communication error
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
Hi I joined recently and I already found many helpful information in this forum. Please forgive my english ( I live in France ) and tell me if my post is in the wrong section.
I have a ford fiesta 2007 tdci 1.6 (it is an mk6 according to my research in french it is labled Ghia VI). One week ago after I left it parket outside (very cold night and I got lazy to enter it) the car didn't started, the jump/pump start failed too. The battery is good, and everything works fine inside (dashboard, lights, ....) except the front windscreen heater (which I am not sure if it used to work without the engine running or not). I plugged an elm327 and I read this fault code p1602 immobilizer/ecm communication error I checked all the fuse in the passenger side and they all seem Ok. No immobilizer warning when I try to start (It goes on for 3 second when I turn first position then off and never comes back again) Any tips on the subject will be welcome. Thanks in advance.
|
Top
|
|
|
#561389 - 23/01/17 10:46 AM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
Thanks so much for your answer, I was busy last week and the car is far from my home. I went Friday and I disconnected the battery and left it the whole weekend, I tried yesterday but it's still the same. Yes me too I strongly think it is a connection issue somewhere due the humidity I bought an electronic spray for the ecu pins, if you can tell me where it is located to check it this evening. Many thanks!!!
|
Top
|
|
|
#561411 - 26/01/17 09:51 AM
Re: P1602 immobilizer/ecm communication error
[Re: dontpannic]
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
Thanks will check that, I took it to a local ford dealer and they refused to handle it, as it is so complicated and need expensive investigation time.
|
Top
|
|
|
#561441 - 01/02/17 07:32 PM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
Hello, I came back today to investigate the problem on this car, I checked some grounds and I wanted to check corrosion around ECU. After unmounted it I was surprised to find out that two pins are tied together (I will join a picture of it). Is it normal by design to have two ECU's pin joined together deliberately ? I know that the guy how changed the started unmounted the ECU so now I am not sure if he did it well or not. Many thanks
|
Top
|
|
|
#561442 - 01/02/17 08:05 PM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
|
Top
|
|
|
#561445 - 01/02/17 09:27 PM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
MountooningTipster
Registered: 26/08/07
Posts: 11633
Loc: here
|
I can not believe that those two pins are meant to be like that, can only guess that the plug has a bent socket and inturn that has forced the ECU pin over and bent it and I would think you would have serious error codes flashing up although it might just be enough to kill the whole car. I could look at my old ECU but currently with a local tuner to see what data they can copy off it. Nick will be along soon to confirm as I can't be certain.
_________________________
MR200 Stage 3 200PS Evans Halshaw Mountune Pro
|
Top
|
|
|
#561446 - 02/02/17 08:01 AM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
n00b
Registered: 16/01/17
Posts: 7
Loc: France
|
Thanks so much for your answer. Yes me too I think the same, but the way it is perfectly bend make me doubtful. Yes it will be great if you have the same ECU to check if some pins are joined together. Do you have any idea where to find a diagram or a piece of paper explaining what each pin if for. Thanks in advance. ps : my ecu is bosh 6S61 - 12A650-VC 5DSC
|
Top
|
|
|
#561448 - 02/02/17 01:27 PM
Re: P1602 immobilizer/ecm communication error
[Re: Zied]
|
MountooningTipster
Registered: 26/08/07
Posts: 11633
Loc: here
|
I think the diagrams are knocking about on the internet, Nick above may know, I won't get my old one back for a while yet.
_________________________
MR200 Stage 3 200PS Evans Halshaw Mountune Pro
|
Top
|
|
|
|
0 registered (),
369
Guests and
0
Spiders online. |
Key:
Admin,
Global Mod,
Mod
|
Registered: 26/06/05
Posts: 23722
|
8577 Members
50 Forums
32273 Topics
561313 Posts
Max Online: 5881 @ 31/12/19 02:16 AM
|
|